Investigating the phase diagram-ionic conductivity isotherm relationship in aqueous solutions of common acids: hydrochloric, nitric, sulfuric and phosphoric acid.

The relationship between phase diagram features around the solid-liquid equilibrium region and ionic conductivity in aqueous solutions is not well understood over the whole concentration range as is the case for acidic aqueous solutions. In this work, we have studied the ionic conductivity (κ) as a function of molar fraction (x) and temperature (T) for four acid/water solutions namely, monoprotic hydrochloric acid (HCl) and nitric acid (HNO3), diprotic sulfuric acid (H2SO4) and triprotic phosphoric acid (H3PO4) along with their binary phase diagrams. The connection between the main features of the phase diagrams and the trends in the ionic conductivity isotherms is established with a new insight on the two pertinent dominant conductivity mechanisms (hopping and vehicular). Ionic conductivity at different temperatures were collected from literature and fitted to reported isothermal (κ vs. x) and iso-compositional (κ vs. T) equations along with a novel semi-empirical equation (κ = f (x, T)) for diprotic and triprotic acids. This equation not only has the best fit for acids with different valency; but also contains four parameters, less than any other similar equation in literature. This work is one of few that advances the understanding of the intricate relationship between structure and ionic transport in various acidic aqueous solutions.

Relationship between microstructure formation and in vitro starch digestibility in baked gluten-starch matrices.

Increased prevalence of diabetes prompts the development of foods with reduced starch digestibility. This study analyzed the impact of adding soluble dietary fiber (inulin-IN; polydextrose-PD) to baked gluten-starch matrices (7.5-13%) on microstructure formation and in vitro starch digestibility. IN and PD enhanced water-holding capacity, the hardness of baked matrices, and lowered water activity in the formulated matrices, potentially explaining the reduced starch gelatinization degree as IN or PD concentration increased. A maximum gelatinization decrease (26%) occurred in formulations with 13% IN. Micro-CT analysis showed a reduction in total and open porosity, which, along with the lower gelatinization degree, may account for the reduced in vitro starch digestibility. Samples with 13% IN exhibited a significantly lower rapidly available glucose fraction (8.56 g/100 g) and higher unavailable glucose fraction (87.76 g/100 g) compared to the control (34.85 g/100 g and 47.59 g/100 g, respectively). These findings suggest the potential for developing healthier, starch-rich baked foods with a reduced glycemic impact.

Chitin nanofibrils assisted 3D printing all-chitin hydrogels for wound dressing.

The direct ink writing technique used in 3D printing technology is generally applied to designing biomedical hydrogels. Herein, we proposed a strategy for preparing all-chitin-based inks for wound dressing via direct ink writing technique. The ß-chitin nanofibers (MACNF) with a high aspect ratio were applied as a nanofiller to modulate the rheological properties of the alkaline dissolved chitin solution. The printing fidelity significantly depends on the MACNF introduction amount to the composite ink. 5-10 wt% MACNF ratio showed superior printing performance. The printed scaffold showed a uniform micron-sized pore structure and a woven network of nanofibers. Due to the good biocompatibility of chitin and the stereoscopic spatial skeleton, this scaffold showed excellent performance as a wound dressing, which can promote cell proliferation, collagen deposition and the angiogenesis of wounds, demonstrating its potential in biomedical applications. This approach successfully balanced the chitinous printability and biofunctions.

Characterization of microcrystalline cellulose prepared from long and short fibers and its application in ibuprofen tablets.

As a bio-based material, microcrystalline cellulose (MCC) has been applied in many fields including pharmaceuticals, foods, and cosmetics in recent years. However, traditional preparation methods of MCC are facing many challenges due to economic and eco-environmental issues. In this study, softwood dissolved pulp was sieved to long fiber (LF) and short fiber (SF), and subsequently to prepare LF-MCC and SF-MCC by hydrochloric acid hydrolysis at different acid dosages (3-7 wt%), reaction times (30-90 min), and temperatures (75-95 °C). The as-obtained MCC products were compared in terms of morphology, size, crystallinity, and chemical structure. The results indicated that the crystallinity and yield of LF-MCC were high, with maximum values of 78.41 % and 98.68 %, respectively. The particle size distribution of SF-MCC was more uniform in the range of 20-80 µm, with a maximum of 59.44 % at 20-80 µm occupancy proportion. Moreover, SF-MCC had a typical rod-like shape and larger surface area as well as better thermal behavior than LF-MCC. When LF-MCC and SF-MCC were used as fillers in the production of ibuprofen tablets, the tablets added with LF-MCC exhibited higher hardness, friability, dissolution rate, and shorter disintegration time. Therefore, this work is very beneficial for the preparation and application of MCC.

Corrosion Inhibition of Expired Cefazolin Drug on Copper Metal in Dilute Hydrochloric Acid Solution: Practical and Theoretical Approaches.

In this work, we studied the corrosion of Cu metal in 0.5 mol L-1 HCl and the inhibition effect of the expired Cefazolin drug. The inhibition efficiency (IE) of Cefazolin varied according to its concentration in solution. As the Cefazolin concentration increased to 300 ppm, the IE increased to 87% at 298 K and decreased to 78% as the temperature increased to 318 K. The expired drug functioned as a mixed-type inhibitor. The adsorption of the drug on the copper surface followed Temkin's adsorption model. The magnitudes of the standard free energy change (ΔGoads) and adsorption equilibrium constant (Kads) indicated the spontaneous nature and exothermicity of the adsorption process. Energy dispersive X-ray (EDX) and scanning electron microscopy (SEM) techniques showed that the drug molecules were strongly attached to the Cu surface. The electrochemical frequency modulation (EFM), potentiodynamic polarization (PP), and electrochemical impedance spectroscopy (EIS) results were in good agreement with the results of the weight loss (WL) method. The density functional tight-binding (DFTB) and Monte Carlo (MC) simulation results indicated that the expired drug bound to the copper surface through the lone pair of electrons of the heteroatoms as well as the π-electrons of the tetrazole ring. The adsorption energy between the drug and copper metal was -459.38 kJ mol-1.

HSP70 Is a Critical Regulator of HSP90 Inhibitor's Effectiveness in Preventing HCl-Induced Chronic Lung Injury and Pulmonary Fibrosis.

Exposure to hydrochloric acid (HCl) can provoke acute and chronic lung injury. Because of its extensive production for industrial use, frequent accidental exposures occur, making HCl one of the top five chemicals causing inhalation injuries. There are no Food and Drug Administration (FDA)-approved treatments for HCl exposure. Heat shock protein 90 (HSP90) inhibitors modulate transforming growth factor-ß (TGF-ß) signaling and the development of chemical-induced pulmonary fibrosis. However, little is known on the role of Heat Shock Protein 70 (HSP70) during injury and treatment with HSP90 inhibitors. We hypothesized that administration of geranylgeranyl-acetone (GGA), an HSP70 inducer, or gefitinib (GFT), an HSP70 suppressant, alone or in combination with the HSP90 inhibitor, TAS-116, would improve or worsen, respectively, HCl-induced chronic lung injury in vivo and endothelial barrier dysfunction in vitro. GGA, alone, improved HCl-induced human lung microvascular endothelial cells (HLMVEC) barrier dysfunction and, in combination with TAS-116, improved the protective effect of TAS-116. In mice, GGA reduced HCl toxicity and while TAS-116 alone blocked HCl-induced chronic lung injury, co-administration with GGA, resulted in further improvement. Conversely, GFT potentiated HCl-induced barrier dysfunction and impaired the antidotal effects of TAS-116. We conclude that combined treatments with HSP90 inhibitors and HSP70 inducers may represent a novel therapeutic approach to manage HCl-induced chronic lung injury and pulmonary fibrosis.

Effects of repeated etching cycles using 15% hydrochloric acid on enamel loss and relative attenuation coefficient in resin infiltration.

BACKGROUND: Resin infiltration is used to mask enamel opacities and the recommended etching cycles are three. However, anecdotal evidence suggests that favorable esthetics outcomes can be obtained by increasing the etching cycles. AIM: To determine the incremental and total enamel loss when enamel surfaces are exposed to multiple etching cycles and to assess the relative attenuation coefficient after multiple etching cycles and resin infiltration treatment. METHODS: Ninety extracted sound human premolars teeth were divided into 9 groups (n = 10); with each consecutive group having one additional etching cycle up to 9 cycles. The teeth were scanned with optical coherence tomography and enamel loss and attenuation coefficient were measured with MATLAB software. Enamel loss (one-way ANOVA, p ≤ 0.05) and attenuation coefficient (two-way ANOVA, p ≤ 0.05) were statistically analyzed. RESULTS: There was a significant total enamel loss of more than 33% found at the 7th etching cycle and more. There was no statistically significant difference in the incremental mean depth of penetration of resin between various etching cycles (F(8, 134) = [2.016], one-way ANOVA, p = 0.185). CONCLUSION: This study recommends that etching should not be repeated more than seven cycles to prevent excessive enamel loss. Following eight etching cycles, resin infiltration penetration appears approximately equal to that of healthy enamel.

The influence of γ-PGA on the quality of cooked frozen crayfish during temperature fluctuations.

The purpose of this study was to compare the influences of gamma-poly glutamic acid (γ-PGA) (1, 2, 3, and 4 %) to see which could outperform conventional cryoprotectant mixture (4 % sorbitol + 4 % sucrose) on cooked crayfish properties, such as physicochemical, textural qualities, oxidation reaction, water distributions, and microstructure integrity, during different freeze-thaw cycles. Crayfish quality characteristics improved significantly as γ-PGA concentration increased compared to control samples.Adding γ-PGA 4 % reduced the carbonyl content from 4.20 to 3.00 nmol/ mg protein during fluctuation-1 (F1), and from 4.15 to 2.80 nmol/ mg protein during fluctuation-2 (F2) compared to control samples. Furthermore, it increased the total sulfhydryl content from 4.15 and 4.76 to 6.19 and 6.47 mol/105 g protein during F1 and F2 and after five freeze-thaw cycles (FTC). This suggests that this concentration was more effective at controlling protein changes than other concentrations. γ-PGA generally enhanced the water-holding capacity by preventing protein denaturation and limiting ice crystal recrystallization. As a result, microstructure stability was evident, texture degradation was avoided, and the crayfish's color was preserved.

Acidification is required for calcium and magnesium concentration measurements in equine urine.

BACKGROUND: Acidification of equine urine to promote dissociation of ion complexes is a common practice for urine ion concentration measurements. The objective of this study was to evaluate the effect of acidification and storage after acidification on calcium (Ca), magnesium (Mg) and phosphate (P) concentrations and on fractional excretion (FE) of these electrolytes. Thirty-two fresh equine urine samples were analysed between December 2016 and July 2020. Complete urinalysis (stick and sediment) was performed on all samples. Ca, Mg, P and creatinine concentrations were measured in supernatant of centrifuged native urine, urine directly centrifuged after acidification and urine centrifuged 1 hour after acidification. Urine was acidified with hydrochloric acid to reach a pH of 1-2. Ca, Mg, P and creatinine concentrations were also measured in blood plasma, and fractional excretion of each electrolyte was calculated. Equality of medians was tested with Friedman tests and Bland-Altman bias plots were used to show the agreement between conditions. RESULTS: Acidification had a statistically significant effect on Ca and Mg concentrations, FECa and FEMg. Bland-Altman plot revealed a strong positive proportional bias between Ca concentration in native and acidified urine with a mean bias of 17.6 mmol/l. For Mg concentration, the difference between native and acidified urine was small with a mean bias of 1.8 mmol/l. The increase in FECa was clinically relevant. Storage of acidified urine had no effect on any of the measured ion concentrations. All P concentrations in native urine samples were below the detection limit of the assay and statistical analysis and calculation of FEP was not possible. CONCLUSIONS: Urine acidification is essential for accurate measurement of Ca and Mg concentrations and therefore FE calculations in equine urine. Storage time of 1 hour after acidification does not significantly change Ca and Mg concentrations.

Sustainable Utilization of Fe(â ¢) Isolated from Laterite Hydrochloric Acid Lixivium via Ultrasonic-Assisted Precipitation to Synthesize LiFePO4/C for Batteries.

Ultrasonic-assisted precipitation was employed to sustainably isolate Fe in the hydrochloric acid lixivium of low-grade laterite for the synthesis of battery-grade iron phosphate. The recovery efficiency of Ni and Co exceeded 99%, while the removal efficiency of the Fe impurity reached a maximum of 95%. Precipitation parameters for the selective isolation of Fe (MgO precipitant, pH 1, 70-80 °C) were optimized and used in ultrasonic precipitation experiments. The use of ultrasonic waves in the precipitation process enhanced micromixing by reducing the size of primary grains and mitigating particle agglomeration, thereby significantly improving the purity of the isolated compound and providing high-quality iron phosphate (FePO4·2H2O). The LiFePO4/C composite prepared from as-precipitated FePO4 exhibited excellent electrochemical performance, with a discharge capacity of 149.7 mAh/g at 0.1 C and 136.3 mAh/g at 0.5 C after 100 cycles, retaining almost 100% cycling efficiency. This novel and facile method for iron removal from laterite acid lixivium not only efficiently removes excess iron impurities leached due to the poor selectivity of hydrochloric acid, but also enables the high-value utilization of these iron impurities. It enhances economic benefits while simultaneously alleviating environmental pressure.

Inhibition of corrosion of an aluminum alloy by rosemary and eucalyptus extracted oils in 1 M hydrochloric acid medium: an experimental and theoretical study.

In this study, we explored aluminum corrosion inhibition field of study in a 1 M HCl solution, harnessing the power of essential oils extracted from rosemary and eucalyptus plants. Our exploration gives a comprehensive analysis of the pivotal factors that shape the corrosion inhibition process. Our scientific journey was marked by a deliberate and systematic approach, encompassing the utilization of gravimetric analysis (weight loss), electrochemical potentiodynamic polarization, and the sophisticated electrochemical impedance spectrometry (EIS) techniques. Our findings unveiled promising and nuanced outcomes, particularly in the area of the electrochemical technique. This method demonstrated remarkable inhibition efficiencies, ranging from 42% to an impressive 92% for rosemary essential oil and from 37 to 84% for eucalyptus essential oil. These results unveiled a dynamic relationship between essential oil concentration and inhibition efficiency, a revelation that further deepens our understanding of the corrosion inhibition process. The inhibition efficiency increased with higher concentrations of essential oil but decreased with elevated temperatures. Furthermore, our analysis traversed into the realms of potentiodynamic and thermodynamic insights. These analytical techniques unearthed the complex mechanisms at play, explaining the pathway followed by the studied inhibitors. They exhibited their prowess by forming protective films on the metal surface, acting as vigilant protectors against the relentless forces of corrosion. Complementing our experimental findings, our study of computational chemistry through density functional theory (DFT) unveiled remarkable insights. It elucidated the spontaneous adsorption process of inhibitor molecules onto the aluminum surface in the presence of H2O solvent. This computational harmony with our experimental results strengthened our confidence in the robustness of our findings. One of the key findings of this study was the superior inhibitory power of camphor in rosemary EO and ß-myrcene in eucalyptus essential oil EO, respectively, attributed to the distinctive characteristics of the active sites found in each compound. The inhibitory effectiveness followed the order ß-myrcene > camphor > borneol > α-pinene > bornyl acetate > p-cymene > 1,8-cineole. These compounds, notable for their distinct active sites, emerged as exceptional agents in the pursuit of effective corrosion inhibition.

Effects of cold atmospheric plasma pre-treatment on maintaining the quality of ready-to-eat drunken red shrimp (Solenocera crassicornis) stored at chilled conditions.

This present study investigated the effect of cold atmospheric plasma (CAP) pre-treatment on the quality of ready-to-eat drunken red shrimp (Solenocera crassicornis) during chilled storage. The shrimp were pre-treated with the CAP at 40 kV and 36 kH for 100 s in a plasma generating equipment before the drunken treatment and compared with an untreated control sample. The results showed that the CAP pre-treatment significantly inhibited the total viable count (TVC) values, total volatile basic nitrogen (TVB-N) content, and polyphenol oxidase (PPO) activity of the drunken shrimp compared to the control treatment. Furthermore, the CAP pre-treatment also significantly maintained the myofibrillar protein (MP) content, texture properties, and a more stable histological structure of muscle fibers compared to the control. High-throughput sequencing results confirmed that the CAP pre-treatment significantly reduced the diversity and abundance of several bacteria in the shrimp. Gas chromatography-ion mobility spectrometry (GC-IMS) analysis detected that the CAP pre-treatment effectively maintained the stability of volatile organic compounds (VOCs). These findings provide valuable theoretical support for the processing and storage of drunken shrimp.

Microbubble Oxidation for Fe2+ Removal from Hydrochloric Acid Laterite Ore Leachate.

After the atmospheric hydrochloric acid leaching method is used to treat laterite ore and initially purify it, the extract that results often contains a significant amount of Fe2+ impurities. A novel metallurgical process has been proposed that utilizes microbubble aeration to oxidize Fe2+ ions in laterite hydrochloric acid lixivium, facilitating subsequent separation and capitalizing on the benefits of microbubble technology, including its expansive specific surface area, negatively charged surface attributes, prolonged stagnation duration, and its capacity to produce active oxygen. The study examined the impacts of aeration aperture, stirring speed, oxygen flow rate, pH value, and reaction temperature. Under optimized experimental conditions, which included an aeration aperture of 0.45 µm, stirring at 500 rpm, a bubbling flow rate of 0.4 L/min, pH level maintained at 3.5, and a temperature range of 75-85 °C, the oxidation efficiency of Fe2+ surpassed 99%. An analysis of the mass transfer process revealed that microbubble aeration markedly enhances the oxygen mass transfer coefficient, measured at 0.051 s-1. The study also confirmed the self-catalytic properties of Fe2+ oxidation and conducted kinetic studies to determine an apparent activation energy of 399 kJ/mol. At pH values below 3.5, the reaction is solely governed by chemical reactions; however, at higher pH values (>3.5), both chemical reactions and oxygen dissolution jointly control the reaction.

Experimental Study on Bio-Reinforcement of Calcareous Sand through Hydrochloric Acid Solution Precipitation into Cementing Solution.

Microbially induced carbonate precipitation (MICP) technology holds great potential in enhancing soil properties. MICP can be employed to enhance the stability and strength of diverse sandy soil, but it has the shortcoming of low curing efficiency. In response to the identified problem, this study aims to investigate an optimized treatment protocol that involves formulating a cementing solution in a hydrochloric acid (HCl) solution to enhance the solidification rate in the MICP reaction and evaluate its effectiveness. The results indicate that when preparing a 1 M cementing solution in a 0.2 M HCl solution, it promotes the rapid bonding of calcareous sand particles, resulting in an unconfined compressive strength (UCS) of 1312.6 kPa in the sand column after five treatments. Compared to the conventional test group, the experimental group containing HCl exhibited an approximately 1357% increase in UCS. The analysis unveiled the pivotal role of metal ions dissolved from calcareous sand by HCl in enhancing the UCS of MICP-treated calcareous sand. The proposed experimental methodology serves as a valuable tool for designing treatment strategies for MICP-cemented calcareous sand in practical engineering applications.

The Penetration Depth of Resin Infiltration Into Enamel: A Systematic Review.

Aims and Objectives: Studies on resin infiltration and its penetration capability are becoming the focus of emerging dentistry. The depth of resin penetration could be a key determining factor in creating a diffusion barrier and in the success of infiltration. The aim of this review article was to evaluate the penetration depth of commercially available resin infiltration in early caries lesions and to identify factors that influence the penetration capability of resin infiltration. Materials and Methods: A literature search was performed in four databases (PubMed, Science Direct, Scopus, and Web of Science) and manual searching from 2009 to December 2022. Eligibility criteria included in vitro studies pertaining to factors affecting the penetration depth of resin infiltration into the enamel. The risk of bias assessment was done by using checklist for reporting in vitro studies (CRIS). Results: The initial search resulted in a total of 297 studies. Twenty-nine were assessed for eligibility, and 23 were selected in the qualitative synthesis. According to the CRIS guidelines, all of the studies were classified as moderate risk of bias. The penetration of resin infiltration is influenced by the enamel surface treatment with hydrochloric acid, formulations containing triethylene glycol dimethacrylate (TEGDMA), the addition of ethanol, penetration time, duration of penetration time, saliva contamination, caries activity, and type of tooth. The hypermineralized surface layer needs to be removed for better resin perfusion. Conclusion: The key to optimal resin infiltration depends on the enamel surface treatment with hydrochloric acid and application technique, infiltration duration, formulation of TEGDMA and ethanol in the resin composition, as well as the type and caries activity of involved teeth. Resin infiltration has superior penetrability compared to fissure sealant, casein phosphopeptide-amorphous calcium phosphate nanocomplexes, flowable composite, adhesive and fluoride varnish. Resin penetration depth may be a critical factor in forming a diffusion barrier and the effectiveness of infiltration in halting the progression of caries.

Enhancement of the Acid Resistance of Silty Clay Using Nano-Magnesium Oxide.

Hydrochloric acid is prevalent in numerous industries; leakage of this acid may cause persistent problems in the soil. The study aims to prevent any adverse impact of acid on the strength characteristics of silty clay soil by modifying the soil's acid resistance. In this study, unconfined compression tests are performed to investigate the strength of contaminated silty clay soil with concentrations of 4%, 8%, and 12% of HCl solution and the strength of treated soil with 0.4%, 0.5%, 0.6%, and 0.8% of nano-magnesium oxide. In addition, the strength of the soil enhanced with nano-MgO contaminated with different concentrations of hydrochloric acid was investigated to assess the effect of nano-MgO on modifying the acid resistance of clay soil. Moreover, the FE-SEM test was performed to analyze the microstructure of the soil under different circumstances. Based on the results, the strength of clay soil decreased due to contamination with the hydrochloric acid solutions; the reduction in strength was more noticeable when the acid solution became more acidic. Adding 0.6% of nano-magnesium oxide enhances the strength by about 114%. Findings show that adding 0.6% nano-MgO to the soil before exposing it to hydrochloric acid can enhance its acid resistance; the strength of the treated soil with nano-MgO was better at resisting the acid than the untreated soil.

Repeated Etching Cycles of Resin Infiltration up to Nine Cycles on Demineralized Enamel: Surface Roughness and Esthetic Outcomes-In Vitro Study.

Resin infiltration (RI) is used to mask enamel opacities. There are three recommended etching cycles. However, anecdotal evidence suggests that favorable esthetics outcomes can be obtained by increasing the etching cycles. This study aimed to evaluate the effects of repeated etching cycles during RI application on esthetic changes and surface roughness of demineralized enamel at multiple treatment stages. Artificial demineralization was prepared on the buccal surface of ninety sound extracted premolars. The teeth were divided into nine groups (n = 10); with each consecutive group having one additional etching cycle up to nine etching cycles. Resin infiltrant was performed twice, first for 3 min (Resin 1) and again for 1 min (Resin 2). Surface roughness and esthetic changes were assessed using a profilometer (Ambios XP-200) and Minolta spectrophotometer, respectively, at baseline (sound enamel), etching, resin 1, resin 2, 7 days, and 28 days post resin applications. Data were analyzed with two-way ANOVA (p < 0.05). There was a significant interaction between the different stages and various groups of etching cycles on surface roughness, F(48, 126) = 3.48, p < 0.001. There was a significant interaction between the different stages and various groups of etching cycles on color changes, F(4, 126) = 1.177, p = 0.045. The surface roughness of demineralized enamel infiltrated with RI was less than that of sound enamel (baseline). There is a significant difference in color changes between resin 1 and resin 2 (p < 0.05). After five etching cycles, RI improved the esthetic of the color of teeth similar to the baseline. Surface roughness and color changes remained constant for 28 days. RI can be considered an effective and predictable treatment option for the restoration of early enamel lesions owing to its better surface characteristics and reliable masking effects. The color stability and surface roughness stay unaltered for up to 28 days.

Dechlorination of waste polyvinyl chloride (PVC) through non-thermal plasma.

Dechlorination is essential for the chemical recycling of waste polyvinyl chloride (PVC) plastics. This study investigated the use of non-thermal plasma (NTP) for chlorine removal, with a focus on the effects of treatment time and discharge power on dechlorination efficiency. The results showed that longer treatment times and higher discharge powers led to better dechlorination performance. The maximum efficiency (98.25%) and HCl recovery yield (55.72%) were achieved at 180 W power after 40 min of treatment where 96.44% of Cl existed in the form of HCl gas, 1.44% in the liquid product, and 2.12% in the solid residue product. NTP at a discharge power of 150 W showed better dechlorination performance compared to traditional thermal pyrolysis treatment in temperatures ranging from 200 to 400 °C. The activation energy analysis of the chlorine removal showed that compared to pyrolysis-based dechlorination (137.09 kJ/mol), NTP-based dechlorination (23.62 kJ/mol) was more easily achievable. This work presents a practical method for the dechlorination of waste PVC plastic using a novel technology without requiring additional thermal and pressure input.

Amino acid analysis for peptide quantitation using reversed-phase liquid chromatography combined with multiple reaction monitoring mass spectrometry.

Amino acid analysis (AAA) can be used for absolute quantitation of standard peptides after acid hydrolysis using 6 M HCl. Obtained individual amino acids can then be quantified by liquid chromatography-mass spectrometry (LC-MS). Achieving baseline separation of non-derivatized amino acids is challenging when reversed-phase (RP) chromatography is used. Several derivatization methods are commonly utilized to address this issue; however, derivatization has several drawbacks, such as derivative instability and lack of reproducibility. Currently, separation of non-derivatized amino acids is typically done using HILIC, but HILIC has problems of poor reproducibility and long column equilibration times. We developed a method to quantify non-derivatized amino acids, including methionine and cysteine, from peptide hydrolysates by RP-LC-MS without special pre-treatment of the samples. Samples were spiked with certified isotopically labeled (13C- and/or 15N-) amino acids as internal standards. The amino acids released from acid hydrolysis were then analyzed by RP-UPLC-MRM-MS and quantified using the analyte/internal standard chromatographic peak area ratios. Peptide quantitation was based on the sum of the individual amino acid concentrations from the known peptide sequences. The resulting method did not require derivatization, used standard C18-based reversed-phase liquid chromatography, did not require external calibration, was robust, and was able to quantify all 17 amino acids for which we had internal standards, including the sulfur-containing amino acids, cysteine and methionine, in their respective oxidized forms. This simple and robust method enabled the absolute quantitation of standard peptides using only acid hydrolysis and a standard RP-UPLC-MRM-MS setup.

Investigation of the effect of hydrochloric acid with different concentrations on mineral trioxide aggregate plug and dentin.

Background: Mineral trioxide aggregate (MTA) becomes a hard mass after setting and making it difficult to remove and can cause significant problems in the retreatment process. The aim of this study was to evaluate the effect of different concentrations of hydrochloric acid (HCl) on MTA dissolution and its effect on dentin. Materials and Methods: In this in vitro study, 45 single-root premolars were selected. Artificially open apex was created in all samples with similar process. The samples were randomly divided into 4 experimental groups of 10, and a control group of 5. Four-millimeter thick apical plugs of Root MTA were placed in all samples in an orthograde manner. HCl was used at concentrations of 3.75%, 7.5%, 15%, and 22.5% (w/v) for the experimental groups and normal saline for the control group. Each sample was exposed to the desired solution for 15 min. Then, MTA retrieval and reaching the working length were attempted with k-file # 30. The times of each sample were recorded. Furthermore, after longitudinal incision of the roots with a disc, the dentin surfaces of canals were examined with a Dino-Lite microscope (×50). Results were analyzed by Shapiro-Wilk test and one-way analysis of variance tests. The level of significance P value was set at 0.05. Results: The lowest average time of reaching working length was observed with group 22.5% that was significantly lower than 15% and 7.5% concentrations (P = 0.005 and P = 0.011). Furthermore, by examining with ×50 of Dino-Lite microscope, no difference was observed on the canal walls. Conclusion: The optimum concentration of HCl was 7.5%. Furthermore, different concentrations of HCl had no significantly different effect on the dentinal canal wall using Dino-Lite microscope with ×50.